Hind Hydraproof Ceramic




Greenpro final logo




Hind Hydraproof Ceramic is an emulsion of high grade Ceramic Polymer in water. It contains the added advantages of ceramic particles which are the heat and cold dissipating elements that give the ability to save on heating and cooling costs. It dries by evaporation to yield a tough, velvety, non-yellowing, watertight surface with highly abrasion resistance and Ultraviolet stability. Hind Hydraproof Ceramic when applied directly to rust will prevent further rusting problem.


Hind Hydraproof Ceramic is used to provide a coating to insulate most building materials from solar heat. Hind Hydraproof Ceramic does not require a primer in most cases due to the unique properties of the material.


  • Energy Saving
  • Cost Saving and Efficient
  • Water tight Membrane
  • Maintain an Attractive Appearance
  • Non Toxic, Non Flammable
  • Built-in rust Inhibitor
  • Prevent Rust
  • Non-Yellowing
  • Excellent adhesion, no primer required in most cases
  • High UV resistance
  • Water based, Single pot material
  • Quick drying
  • High Solar Reflectivity
  • Temperature Reduction
  • Highly Flexible
  • Corrosion and Abrasion Resistance
  • Fungal Resistance


 Brush or Roller

 Pre wet the brushes and rollers to avoid clogging. Apply two coats straight from the container. Allow two hours between conventional spray.

Airless Spray

Thin with up to 10% clean water to aid atomization. Use a tip orifice of 0.5 micrometers or larger. Apply the material in two even coats. Allow two hours between coats. Do not apply if temperature is or will fall below 100C or high humidity, rain or dew as Hind Hydraproof Ceramic will not cure properly. If the conditions are hot or windy, and it is necessary to coat in these conditions the surface should be cooled using water hose. Hind Hydraproof Ceramic can be applied over the damp cool surface. If Hind Hydraproof Ceramic is not dry within one hour, cease coating immediately. Where the application is used for the collection of drinking water, down pipes should be kept open until the area has had two or three rinses with rain water. Surface must be cleaned, dried and free of any oil, grease or dirt by approved method prior to application of Hind Hydraproof


Two coats are recommended for dry film of not less than 300 microns (0.3 mm). Allow two hours to dry before apply second coat.


 Mix thoroughly with a flat stirrer or mechanical mixer before using. Hind Hydraproof Ceramic dose not normally need to be thinned but if considered necessary, 10% of clean water may be added.


Theoretical coverage 4.0 Sq. Mtr/Litre/Coat
Recommended Coats 2 Coats


Color White / Cream / Grey
Coating Type Ceramic Coating
Cleaning Water
Flash Point None
Solid by Volume 60%
Film Thickness 300 micron (Minimum)
Drying Time 30 minutes / 250C
Recoating Time 2 hours
Min. Application Temperature 100C
Max. Application Temperature 350C






Solar Reflectance 93%
Solar Absorbance 7%
Thermal Emission 92%
Transmittance 0% Define as opaque material


Surface Adhesion >15 ksc (ASTM C-633)
Flexibility No cracking breakage
Elongation -500% (ASTM D-412)
Fungal Resistance No fungal growth
Water Transmission No water transmit
Vapour Transmission 0.1 perms (ASTM E-96)
Chemical Resistance No corrosion
Maximum Service 1200C
Temperature No cracking breakage
Fire Resistance (ASTM E-84) Flame spread 5

Fuel contribution 0

Smoke density 0


12 months from the date of manufacture in unopened condition. To be stored in a cool and dry place away from direct sunlight.


1, 4, 20, 200 Kg in HDPE Container.



Hind Hydraproof Ceramic is non-toxic non-flammable and ingestion is to be avoided. Any splashes to the skin must be washed with water. If contact with eyes occurs, wash well immediately with water and seek medical advice.













































Print Friendly
Reviews (0)


There are no reviews yet.

Be the first to review “Hind Hydraproof Ceramic”

Your email address will not be published. Required fields are marked *